MASCHINE for Live by Elton47 Report an issue

How to use MASCHINE MK3, MIKRO MK3 and MASCHINE+ with Ableton Live 12

There are three ways to play Ableton Live 12 from a MASCHINE MK3, MIKRO MK3 or MASCHINE+. Here is what each one does, what it needs and how you set it up.

I'm Elton, and I make one of them, MASCHINE for Live. So I say so where it comes up.

The three ways at a glance

WayControllersLiveWhat you set up
The MASCHINE plug-inMK3, MIKRO MK3, MASCHINE+Live 12The plug-in on a Live track
NI's MIDI mode templateMK3Live 12.1 or newerNI's script in Live's program folder, NI's template in Controller Editor
MASCHINE for LiveMK3, MIKRO MK3, MASCHINE+Live 12.0 or newerCopy one folder, plug in, start Live

1. NI's MASCHINE plug-in, inside Live

You load MASCHINE as a plug-in on a Live track. The controller then works the plug-in the way it works the MASCHINE software: its sounds, its patterns, its own mixer and your Expansions.

This is the way to go if you want MASCHINE itself inside a Live set. The controller plays MASCHINE, not Live. Live's own clips, devices and mixer stay on the mouse.

You need: the MASCHINE software from Native Access.

2. NI's MIDI mode, with a Controller Editor template

For the MASCHINE MK3, NI offers a template and a MIDI Remote Script for Live 12.1 and newer, and older ones for Live 11 and before. The controller then works as a MIDI controller for Live. NI's template manual lists what each button does.

You copy NI's script into Live's own program folder, pick it in Live's settings and load the template in NI's Controller Editor. When no MASCHINE plug-in is loaded in your set, the controller switches to Live by itself. NI's support article (opens in a new tab) has the steps for Windows and macOS.

NI has no official template for the MIKRO MK3. The article doesn't list the MASCHINE+.

You need: Live 12.1 or newer, NI's Controller Editor and NI's files from that article.

3. MASCHINE for Live

This one is mine. MASCHINE for Live is a script for Live 12 that talks to the controller over USB itself. So there's no MIDI mode, no template and no Controller Editor. The controller works Live the way it works MASCHINE.

Setup: copy one folder into Live's User Library, plug in your MASCHINE and start Live. Live finds the script by itself. Nothing to install, no admin rights asked, nothing to set up in Live. The setup guide has every step.

You need: Live 12.0 or newer (Intro, Standard or Suite), Windows 10 / 11 or macOS, and the MASCHINE software installed. It brings the drivers. You don't have to open it.

It's paid, in two editions: one for the MIKRO MK3, and one for the MK3, MASCHINE+ and MIKRO MK3. See the editions or try every button first in the manual's Tour.

FAQ

My MK3 doesn't work in Live 12. What can I check?

First, is the MASCHINE software installed? It brings the controller's drivers. Then it depends on the way you use. NI's template needs Live 12.1 or newer, NI's script in Live's program folder and the template in Controller Editor. With MASCHINE for Live, the folder goes into Live's User Library, in Remote Scripts. Its setup guide shows every step, and I answer every message at support@elton47.com.

Do I need the MASCHINE software?

Yes, installed. It brings the controller's drivers. For the plug-in way, MASCHINE is what you play inside Live. With MASCHINE for Live you don't have to open it.

Does the MIKRO MK3's screen work in Live?

NI has no official Live template for the MIKRO MK3. With MASCHINE for Live, the screen shows the mode and track, tempo, swing and volume as you change them, and device parameters with their names and values.

Does it work on Windows 10?

MASCHINE for Live runs on Windows 10 and 11 and on macOS, with nothing to install and no admin rights asked. For NI's two ways, check what NI lists.

What about Live 11?

MASCHINE for Live v2 is for Live 12. For Live 11 there is v1.6.1, my previous version. NI's templates have Live 11 versions too.